Systematics MIG300SM Power Source

MIG300SM Power Source

STANDARD FEATURES

• Tapped transformer design for perfect voltage control
• 300 amps output
• 100% duty cycle
• Singe Phase 208 or 230 volts
• Twelve voltage selections
• Rugged steel cabinet
• Recessed front panel provides protection of controls
• Quiet ball bearing fan motor is lifetime lubricated
• Insulated output terminals provide maximum safety
• Thermal overload protection devices on transformer and diode heatsink
• Ammeter and Voltmeter
• Built in 50 amp circuit breaker
• Auxilary 115 volt outlet on front panel
• 115 volt contactor circuit
• 10 foot power input cable
• Wheel kit / cylinder rack

SPECIFICATIONS 

POWER INPUT REQUIREMENTS:

Voltage                           208/230 volts AC

Phase                             Single Phase

Frequency                       50/60 hertz

Current                            44/40 amps

POWER OUTPUT:

Open Circuit Voltage        18-42 volts

Welding Current               300 amps @ 26 volts

Duty Cycle                      100%

DIMENSIONS:                 29″H X 22″W X 38″D

WEIGHT:                        300 pounds

WIRE FEEDERS RECOMMENDED FOR USE WITH THE MIG 300 SM:

FW 112 Conventional Style Wire Feeder

Standard Features of FW 112 Wire Feeder:

• Feeds .020 inch through 5/64 inch wire
• 50 to 800 IPM wire feed speed range
• Insulated single roll wire drive system
• Accomodates 4, 8, or 12 inch spools
• Supplied with 15 foot Cable Assembly

                    Control Cable

                    Weld Cable

                    Gas Hose

• Choice of MIG Torch connection

                    Systematics – standard

                    Bernard, Tweco or European style – optional

• Purge / Open Circuit Voltage switch
• Solid state wire feed speed control
• Drive rolls are geared together
• Electronic wire feed brake

SPECIFICATIONS:

Power Input Requirements:

Voltage                          115V AC

Phase                            single phase

Frequency                      50/60 hertz

Current                           3 amps 

Wire Size Range:

Hard Wire                      .020 thru 1/16 inch

Soft Wire (Alum.)            .035 thru 1/16 inch

Flux Cored Wire             .035 thru 5/64 inch 

Dimensions:

Height                             10 1/2 inches             

Width                              7 1/4 inches

Depth                              18 inches

Weight                            30 pounds

SC112 Suitcase Style Wire Feeder

Standard Features of SC112 wire feeder:

• Feeds .020 inch through 5/64 inch wire
• 50 to 800 IPM wire feed speed range
• Insulated single roll wire drive system
• Accomodates 4, 8, or 12 inch spools (with optional adapters)
• Supplied with 15 foot Cable Assembly

                    Control Cable (15 ft.)

                    Weld Cable (14 ft.)

                    Gas Hose (20 ft.)

• Choice of MIG Torch connection

                    Systematics – standard

                    Bernard, Tweco or European style – optional

• Purge / Open Circuit Voltage switch
• Solid state wire feed speed control
• Drive rolls are geared together
• Electronic wire feed brake
• Dynamic Braking System
• Non-conductive case

SPECIFICATIONS:

Power Input Requirements:

Voltage                          115V AC

Phase                            single phase

Frequency                      50/60 hertz

Wire Size Range:

Hard Wire                      .020 thru 1/16 inch

Soft Wire (Alum.)            .035 thru 1/16 inch

Flux Cored Wire             .035 thru 5/64 inch

Dimensions:

Height                            10 1/2 inches             

Width                             7 1/4 inches

Depth                             18 inches

Weight                           30 pounds