MIG300SM Power Source
STANDARD FEATURES
- Tapped transformer design for perfect voltage control
- 300 amps output
- 100% duty cycle
- Singe Phase 208 or 230 volts
- Twelve voltage selections
- Rugged steel cabinet
- Recessed front panel provides protection of controls
- Quiet ball bearing fan motor is lifetime lubricated
- Insulated output terminals provide maximum safety
- Thermal overload protection devices on transformer and diode heatsink
- Ammeter and Voltmeter
- Built in 50 amp circuit breaker
- Auxilary 115 volt outlet on front panel
- 115 volt contactor circuit
- 10 foot power input cable
- Wheel kit / cylinder rack
SPECIFICATIONS
POWER INPUT REQUIREMENTS:
Voltage | 208/230 volts AC |
Phase | Single Phase |
Frequency | 50/60 hertz |
Current | 44/40 amps |
POWER OUTPUT:
Open Circuit Voltage | 18-42 volts |
Welding Current | 300 amps @ 26 volts |
Duty Cycle | 100% |
Dimensions | 29″H X 22″W X 38″D |
Weight | 300 lbs |
WIRE FEEDERS RECOMMENDED FOR USE WITH THE MIG 300 SM:
FW 112 Conventional Style Wire Feeder
Standard Features of FW 112 Wire Feeder:
- Feeds .020 inch through 5/64 inch wire
- 50 to 800 IPM wire feed speed range
- Insulated single roll wire drive system
- Accomodates 4, 8, or 12 inch spools
- Supplied with 15 foot Cable AssemblyControl Cable
Weld Cable
Gas Hose - Choice of MIG Torch connectionSystematics – standard
Bernard, Tweco or European style – optional - Purge / Open Circuit Voltage switch
- Solid state wire feed speed control
- Drive rolls are geared together
- Electronic wire feed brake
SPECIFICATIONS:
POWER INPUT REQUIREMENTS:
Voltage | 115V AC |
Phase | Single phase |
Frequency | 50/60 hertz |
Current | 3 amps |
WIRE SIZE RANGE:
Hard Wire | .020 thru 1/16 inch |
Soft Wire (Alum.) | .035 thru 1/16 inch |
Flux Cored Wire | .035 thru 5/64 inch |
DIMENSIONS:
Height | 10 1/2 inches |
Width | 7 1/4 inches |
Depth | 18 inches |
Weight | 30 pounds |
SC112 Suitcase Style Wire Feeder
Standard Features of SC112 wire feeder:
- Feeds .020 inch through 5/64 inch wire
- 50 to 800 IPM wire feed speed range
- Insulated single roll wire drive system
- Accomodates 4, 8, or 12 inch spools (with optional adapters)
- Supplied with 15 foot Cable AssemblyControl Cable (15 ft.)
Weld Cable (14 ft.)
Gas Hose (20 ft.) - Choice of MIG Torch connectionSystematics – standard
Bernard, Tweco or European style – optional - Purge / Open Circuit Voltage switch
- Solid state wire feed speed control
- Drive rolls are geared together
- Electronic wire feed brake
- Dynamic Braking System
- Non-conductive case
SPECIFICATIONS:
POWER INPUT REQUIREMENTS:
Voltage | 115V AC |
Phase | Single phase |
Frequency | 50/60 hertz |
WIRE SIZE RANGE:
Hard Wire | .020 thru 1/16 inch |
Soft Wire (Alum.) | .035 thru 1/16 inch |
Flux Cored Wire | .035 thru 5/64 inch |
DIMENSIONS:
Height | 10 1/2 inches |
Width | 7 1/4 inches |
Depth | 18 inches |
Weight | 30 pounds |
Systematics MIG300SM Power Source was last modified: March 31st, 2020 by